Magnetic Reed Switch

Product # FGD-0006

The magnetic reed switch may be used with all Sensaphone models to detect any unauthorized entry or intrusion. They are usually installed on doors and windows to detect their opening and closing. Several magnetic reed switches may be wired in series.

Infra-Red Motion Detector

Product # FGD-0007

The passive infra-red motion detector can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Its range of detection covers approximately forty feet of area. Multiple sensors can be wired in series to a single output.

Spot Water Detector

Product # FGD-0013

The water detection sensor can be used with all Sensaphone models to detect the presence of water on a horizontal surface. Independently powered by internal lithium batteries. The batteries should last for approximately 3-5 years. When the batteries start to run down, the sensor will automatically cause an alarm dial out when no water is present. Multiple sensors can be wired in series to a single input.

Temp Alert

Product # FGD-0022

The Temp Alert can be used with all Sensaphone models to monitor air temperature from -30° to 130°F (-34° to 54°C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When the temperature exceeds the setting, the sensor triggers an alarm. The temp alert can be mounted to any wall or vertical surface. Multiple temp alerts may be wired in parallel to a single input. It requires no power for operation and mounts easily on any flat surface.

Humidistat

Product # FGD-0027

The Humidistat can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic with a brushed goldtone dial plate and a beige cover. A nylon sensing element provides long life and accurate humidity control. With a range of 10% to 60% RH level, the sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input.

Smoke Detector 110VAC

Product # FGD-0049

The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.

Smoke Detector 110VAC with Battery backup

Product # FGD-0049-B

The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power, but also includes internal battery backup. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.

Humidity Transmitter (4-20mA)

Product # FGD-0052

A space mount, low profile humidity transducer. Transmits actually humidity levels to Sensaphone for programmable high and low alarm limits. Does not come with wire.

PowerOut Alert Model PS-110

Product # FGD-0054

A compact power outage monitoring device to detect power failures. Easily plugs into any 110 VAC receptacle outlet for operation. Comes with 15 feet of wire.

Zone Water Detector

Product # FGD-0056

The Sensaphone zone water detector is for detecting the presence of water on a floor or in a FALSE ceiling. It comes with 10′ of WaterRope capable of covering a larger area than the FGD-0013 water sensor. Up to ten WaterRopes can be cascaded from a single sensor for even greater coverage. Works with all Sensaphone products and operates on two AA batteries (installed).

Extra 10' Water Detection Rope

Product # FGD-0063

Extends the water detection rope on the FGD-0056 sensor by an additional 10 feet.

Carbon Monoxide (CO) Sensor

Product # FGD-0065

Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. The 1″ x .5″ LCD displays the PPM and menu parameters. The sensor will require a 24VDC power supply to operate (Part # FGD-0053).

Air Quality Sensor

Product # FGD-0066

The Sensaphone Indoor Air Quality sensor will allow you to monitor levels of pollution from 0–100% with any Sensaphone that will accept a 4-20mA input signal. Popular applications include schoolrooms, office buildings, and parking garages. The Air Quality sensor uses a tin dioxide semiconductor sensor to detect oxidizable gases and is specially designed to have high sensitivity to gaseous organic materials which are components of indoor air pollutants. These air contaminants include cigarette smoke, cooking exhaust, automobile exhaust, solvents and many others. The sensor will require a 24VDC power supply to operate. (Part # FGD-0053)

Carbon Dioxide (CO2) Sensor

Product # FGD-0068

The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0053)

Remote Temperature Sensor 2.8K

Product # FGD-0100

The 2.8K Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured, however this model is recommended to be located in clean, dry environment. For outdoor use model FGD-0101 is recommended.

2.8K Weatherproof Temperature Sensor

Product # FGD-0101

The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments.

2.8K Weatherproof Temperature Sensor w/Calibration Certificate

Product # FGD-0101-NIST

The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. With NIST temperature certification.

10K Remote Weatherproof Temperature Sensor

Product # FGD-0102

The 10K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments.

10K Indoor Decorator Zone Temperature Sensor

Product # FGD-0103

The 10K indoor decorator zone temperature sensor offers precision room temperature sensing in an attractive wall-mounted enclosure. Accurate to 0.36°F (0.2°C) with a sensing range of 35° to 140°F. The indoor decorator comes in a beige plastic enclosure, with a tan metal face plate. The sensor is designed to be wall-mounted indoors where appearance is important. The separate base plate may be mounted directly to the drywall or on a standard electrical outlet box without adapters. The cover is secured with tamper resistant hex screws.

10K Outdoor Air Weatherproof Temperature Sensor

Product # FGD-0104

The 10K Outdoor Air Weatherproof Temperature sensor is a sensitive temperature element with a stainless steel tube sheathe. It is mounted inside a ventilated, treated weather-resistant PVC shield to minimize radiant energy effects and mounted on a weatherproof outlet box for easy outdoor installation. Accurate to ±0.36°F (0.2°C) with a sensing range of -30° to 140°F. Eight feet of 24AWG wire is included.

10K Immersion Temperature Sensor

Product # FGD-0105

The 10K Immersion temperature sensor is a waterproof temperature sensor for measuring the temperature of fluids inside a pipe. It's constructed of brass WEL-B thermowell (which screws into a customer-supplied 0.5″ NPT saddle or Thredolet® fitting in a pipe). It fits into a thermowell via a brass 0.125″ NPT fitting. Accurate to ±0.36°F (0.2°C) and has a sensing range of 10° to 230°F. It also includes 8′ of 24AWG wire.

2.8K Temperature Sensor with Glass Bead Vial

Product # FGD-0107

The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. This is a highly recommended sensor for every cold storage application.

Float Switch

Product # FGD-0222

The FGD-0222 float switch is a plastic side mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of the tank. This style float switch can be rotated for Normally Open or Normally Closed operation. Combine two switches at different levels for high and low level or pump control or alarming.