Magnetic Reed Switch

Product # FGD-0006

The magnetic reed switch may be used with all Sensaphone models to detect any unauthorized entry or intrusion. They are usually installed on doors and windows to detect their opening and closing. Several magnetic reed switches may be wired in series.

Infra-Red Motion Detector

Product # FGD-0007

The passive infra-red motion detector can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Its range of detection covers approximately forty feet of area. Multiple sensors can be wired in series to a single output.

Accessory Wire

Product # FGD-0010

50ft. of 22-gauge shielded wire for connecting sensors to your sensaphone.

Spot Water Detector

Product # FGD-0013

The water detection sensor can be used with all Sensaphone models to detect the presence of water on a horizontal surface. Independently powered by internal lithium batteries. The batteries should last for approximately 3-5 years. When the batteries start to run down, the sensor will automatically cause an alarm dial out when no water is present. Multiple sensors can be wired in series to a single input.

Temp Alert

Product # FGD-0022

The Temp Alert can be used with all Sensaphone models to monitor air temperature from -30° to 130°F (-34° to 54°C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When the temperature exceeds the setting, the sensor triggers an alarm. The temp alert can be mounted to any wall or vertical surface. Multiple temp alerts may be wired in parallel to a single input. It requires no power for operation and mounts easily on any flat surface.

Humidistat

Product # FGD-0027

The Humidistat can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic with a brushed goldtone dial plate and a beige cover. A nylon sensing element provides long life and accurate humidity control. With a range of 10% to 60% RH level, the sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input.

Express II 8 In0put Card Slot 2

Product # FGD-0035

Expands the inputs on your Sensaphone Express II with eight more channels. Labeled for Inputs 9 - 16.

Express II 8 Input Card Slot 3

Product # FGD-0036

Expands the inputs on your Sensaphone Express II with eight more channels. Labeled for Inputs 17 - 24.

Express II 8 Input Card Slot 4

Product # FGD-0037

Expands the inputs on your Sensaphone Express II with eight more channels. Labeled for Inputs 25 - 32.

Express II 8 Input Card Slot 5

Product # FGD-0038

Expands the inputs on your Sensaphone Express II with eight more channels. Labeled for Inputs 33 - 40.

Express II 8 Output Card Slot 1

Product # FGD-0040

Adds eight relay outputs to your Sensaphone Express II. Labeled for Outputs 1 - 8.

Express II 8 Output Card Slot 2

Product # FGD-0041

Adds eight more relay outputs to your Sensaphone Express II. Labeled for Outputs 9 - 16.

Smoke Detector 110VAC

Product # FGD-0049

The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.

Smoke Detector 110VAC with Battery backup

Product # FGD-0049-B

The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power, but also includes internal battery backup. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.

Smoke Detector 220V

Product # FGD-0049-220V

The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 220VAC 50Hz power. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.

Accessory Wire

Product # FGD-0051

4-Conductor RS-485 Cable - SCADA expansion. Used to connect the Input/Output expansion modules to the main SCADA 3000 unit. Sold by the foot.

Humidity Transmitter (4-20mA)

Product # FGD-0052

A space mount, low profile humidity transducer. Transmits actually humidity levels to Sensaphone for programmable high and low alarm limits. Does not come with wire.

24V Power Supply for 4-20mA Sensors

Product # FGD-0053

A 24V power supply for use with most 4-20mA sensors. It is required when connecting the humidity transmitter to any Sensaphone that does NOT provide external 24V DC power. The Sensaphone SCADA 3000 and Express II are the only units that supply their own power.

PowerOut Alert Model PS-110

Product # FGD-0054

A compact power outage monitoring device to detect power failures. Easily plugs into any 110 VAC receptacle outlet for operation. Comes with 15 feet of wire.

Telephone Adapter UK

Product # FGD-0055

Converts US RJ-11 telephone connector to UK style.

Zone Water Detector

Product # FGD-0056

The Sensaphone zone water detector is for detecting the presence of water on a floor or in a FALSE ceiling. It comes with 10′ of WaterRope capable of covering a larger area than the FGD-0013 water sensor. Up to ten WaterRopes can be cascaded from a single sensor for even greater coverage. Works with all Sensaphone products and operates on two AA batteries (installed).

External Microphone Attachment

Product # FGD-0057

Provides listen-in and/or high sound alarm capability at a remote location away from your Sensaphone. Comes with 25 feet of wire.

Extra 10' Water Detection Rope

Product # FGD-0063

Extends the water detection rope on the FGD-0056 sensor by an additional 10 feet.

Dual Setback Thermostat for 400/800

Product # FGD-0064

For use exclusively with the Sensaphone 400 and 800, this is a "setback" thermostat with an LCD readout. It lets you enter the desired setpoint for both your "away" and "home" temperatures. A control signal, sent from your Sensaphone, switches between these two settings.

Carbon Monoxide (CO) Sensor

Product # FGD-0065

Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. The 1″ x .5″ LCD displays the PPM and menu parameters. The sensor will require a 24VDC power supply to operate (Part # FGD-0053).

Air Quality Sensor

Product # FGD-0066

The Sensaphone Indoor Air Quality sensor will allow you to monitor levels of pollution from 0–100% with any Sensaphone that will accept a 4-20mA input signal. Popular applications include schoolrooms, office buildings, and parking garages. The Air Quality sensor uses a tin dioxide semiconductor sensor to detect oxidizable gases and is specially designed to have high sensitivity to gaseous organic materials which are components of indoor air pollutants. These air contaminants include cigarette smoke, cooking exhaust, automobile exhaust, solvents and many others. The sensor will require a 24VDC power supply to operate. (Part # FGD-0053)

Mini Surge Protector- Power and Phone

Product # FGD-0067

The Traveler surge suppressor offers complete AC and phone line surge suppression for your Sensaphone and other electronic devices. The compact housing weighs less than 4 ounces. The retractable plug prevents scratching of expensive portable electronics. A set of RJ11 telephone line suppression jacks protect dialup and voice/modem lines. The suppressor offers 2 total outlets in a space saving direct plug-in format and diagnostic LEDs to warn of wiring problems and suppressor damage. $50,000 Ultimate Lifetime Insurance (USA & Canada Only).

Carbon Dioxide (CO2) Sensor

Product # FGD-0068

The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0053)

Remote Temperature Sensor 2.8K

Product # FGD-0100

The 2.8K Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured, however this model is recommended to be located in clean, dry environment. For outdoor use model FGD-0101 is recommended.

2.8K Weatherproof Temperature Sensor

Product # FGD-0101

The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments.

2.8K Ultra Low -85°C Temperature Sensor with Teflon

Product # FGD-0101-TEF

The 2.8K Ultra Low -85°C Temperature Sensor with Teflon enables monitoring temperatures at a location away from a Sensaphone unit. The Teflon coated wire will withstand temperatures down to -85°C. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. NIST temperature certification is available.

10K Remote Weatherproof Temperature Sensor

Product # FGD-0102

The 10K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments.

10K Indoor Decorator Zone Temperature Sensor

Product # FGD-0103

The 10K indoor decorator zone temperature sensor offers precision room temperature sensing in an attractive wall-mounted enclosure. Accurate to 0.36°F (0.2°C) with a sensing range of 35° to 140°F. The indoor decorator comes in a beige plastic enclosure, with a tan metal face plate. The sensor is designed to be wall-mounted indoors where appearance is important. The separate base plate may be mounted directly to the drywall or on a standard electrical outlet box without adapters. The cover is secured with tamper resistant hex screws.

10K Outdoor Air Weatherproof Temperature Sensor

Product # FGD-0104

The 10K Outdoor Air Weatherproof Temperature sensor is a sensitive temperature element with a stainless steel tube sheathe. It is mounted inside a ventilated, treated weather-resistant PVC shield to minimize radiant energy effects and mounted on a weatherproof outlet box for easy outdoor installation. Accurate to ±0.36°F (0.2°C) with a sensing range of -30° to 140°F. Eight feet of 24AWG wire is included.

10K Immersion Temperature Sensor

Product # FGD-0105

The 10K Immersion temperature sensor is a waterproof temperature sensor for measuring the temperature of fluids inside a pipe. It's constructed of brass WEL-B thermowell (which screws into a customer-supplied 0.5″ NPT saddle or Thredolet® fitting in a pipe). It fits into a thermowell via a brass 0.125″ NPT fitting. Accurate to ±0.36°F (0.2°C) and has a sensing range of 10° to 230°F. It also includes 8′ of 24AWG wire.

2.8K Temperature Sensor with Glass Bead Vial

Product # FGD-0107

The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. This is a highly recommended sensor for every cold storage application.

2.8K Temperature Sensor with Glass Bead Vial and Teflon Cable

Product # FGD-0107-TEF

The FGD-0107-TEF is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. The Teflon coated wire will withstand temperatures down to -85°C. This is a highly recommended sensor for every cold storage application below -20°F.

Multi-Point Wireless I/O

Product # FGD-0205

The multi-point wireless I/O system is ideal if you need to connect one or two dry contacts and/or a 4-20mA transducer to a Sensaphone that is too far (or too expensive) to run cable. The system will replicate these sensors up to a distance of 600′ indoors or up to 4 miles line of site (flat terrain, raised antennas). The system includes a matched 1 Watt 900MHz transmitter and receiver. Two 24V power supplies and omnidirectional antennas are included. Built-in leds indicate RF link and dry contact status.

J Type Thermocouple/4-20mA Converter

Product # FGD-0220

The thermocouple to 4-20mA converter is useful when monitoring very high or very low temperatures that can not be monitored with a standard Sensaphone temperature sensor. Thermocouples are available in a variety of packages that may be perfectly suited to your measuring application. Each thermocouple input module provides a single channel of thermocouple input which is filtered, isolated, amplified, linearized and converted to a 4-20mA output. Isolation is provided by transformer coupling, using a proprietary technique to suppress transmission of common mode spikes or surges. The modules have excellent stability over time and do not require recalibration.

USB to RS-232 Converter

Product # FGD-0221

Configure your Sensaphone through serial communication using newer PCs not equipped with a serial port.

Float Switch

Product # FGD-0222

The FGD-0222 float switch is a plastic side mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of the tank. This style float switch can be rotated for Normally Open or Normally Closed operation. Combine two switches at different levels for high and low level or pump control or alarming.

Sensaphone 2800 Outdoor Weatherproof Antenna Kit

Product # FGD-2810

The FGD-2810 Outdoor Weatherproof Antenna kit is designed to work with the Sensaphone 2800 Environmental Monitoring System. The weatherproof antenna allows you to place your Sensaphone 2800 in a location that would normally have reduced signal contact with the wireless sensors (such as in a metal cabinet or outside a building). It includes a mast mounting kit which includes a heavy duty steel bracket, and a pair of U'-bolts, this kit allows installation on masts up to 2.0" in diameter.

Serial-to-Ethernet Device Server for Sensaphone 2000 or SCADA 3000

Product # FGD-0300

The Serial-to-Ethernet Device Server allows you to access your Sensaphone 2000 or SCADA 3000 anywhere on a local LAN or the Internet. Simply connect the device to the serial port on your Sensaphone and connect the Ethernet jack to your network. The software included with the device server will route your computer's serial port to the network-connected device server, thus establishing a fast, direct connection to your Sensaphone.

SCADA 3000 Universal Input Module

Product # FGD-3010

The SCADA 3000 Universal Input Module is an optional component for use with the SCADA 3000 system. The input channels are identical to those included on the SCADA 3000 main unit. The Universal Input Module features eight channels that can be configured to interface with several different types of sensors and transducers, including: Normally Open/Normally Closed dry contacts, digital logic, Run time accumulation, 0-5V analog, 4-20mA analog and 10K thermistor (°C & °F). The module features 12-bit resolution, differential inputs, 24V supply for powering 4-20mA loops and low-power operation. Each input is protected by a 1500 Watt transient suppressor. In addition, a microprocessor watchdog circuit is integrated to maintain system reliability. LED indicators are provided to show system power and module operation via a blinking pulse LED.

SCADA 3000 Pulse Count Module

Product # FGD-3020

The SCADA 3000 Pulse Count Module features four totalizing pulse count channels and four virtual channels that can be programmed to calculate various rates or to display count overflow. The module has four pulse count channels, each of which is capable of counting pulses at a rate of up to 10,000 pulses per second (10KHz). Each channel will totalize pulses up to one million and then reset to zero. The four virtual channels can be programmed to calculate the pulse as either pulses per second, pulses per minute or pulses per hour. The module is compatible with dry contact or solid state pulse generating devices such as relays or switches. The module may also be connected to the logic output of another solid state computer device (e.g., Open Collector, TTL, CMOS). The module includes adjustable filtering for each channel to prevent counting errors generated by the bounce from slow-moving switches.

SCADA 3000 Relay Output Module

Product # FGD-3040

The SCADA 3000 Relay Output Module is an optional component for use with the SCADA 3000 system. The output channels are identical to those included on the SCADA 3000 main unit. The Relay Output Module features eight latching relay outputs that can be used to switch equipment on and off. The relays are rated at 2 Amps at 125VAC and have integral contact protection. They may be controlled manually or automatically via a ladder program or C-program. In addition, a microprocessor watchdog circuit is integrated to maintain system reliability. LED indicators are provided to show system power and module operation via a blinking pulse LED.

SCADA 3000 Analog Output Module

Product # FGD-3050

The SCADA 3000 Analog Output Module features four analog output signals that can be configured as 4-20mA, 0-20mA, or 0-10V. The outputs can be used to control equipment, drive digital displays, or provide information to other computer devices. The individual outputs are capable of driving up to 1000 Ohms. They may be controlled automatically via a ladder program or C-program. The module also features a microprocessor watchdog circuit to maintain system reliability. LED indicators are provided to show system power and module operation via a blinking pulse LED.

SCADA 3000 Annunciator Module

Product # FGD-3060

The SCADA 3000 Annunciator Module provides 8 programmable LED indicators to display the status of assigned I/O points. The LEDs are bi-color (red/amber), which means that each LED is always on, thereby preventing a FALSE reading due to a burned-out LED. Red indicates an active or ON condition and Amber indicates an inactive or OFF condition. The Annunciator LEDs appear as two-state (ON/OFF) outputs in the SCADA 3000 software. The Annunciator module is housed in a 1/8 DIN enclosure for convenient panel mounting.

SCADA 3000 Power Supply

Product # FGD-3100

Hard wired power supply for SCADA 3000 main power. Works with 110VAC or 220VAC.

SCADA 3000 Power Supply 110VAC

Product # FGD-3110

Plug in power supply for SCADA 3000 main power. For 110VAC outlets only.

SCADA 3000 5Ah Battery Supply

Product # FGD-3200

Battery backup kit for SCADA 3000. Backup time during a power failure is dependant on number of accessories, but 8 hours is typical.

SCADA 18 Ah Battery Supply

Product # FGD-3210

SCADA 3000 Spare Fuse Kit

Product # FGD-3220

Contains additional replacement fuses for the SCADA 3000 power supply.

CELL 682 Wall Mounted Antenna

Product # FGD-CELL-ANT

The FGD-CELL-ANT is designed to work with the Sensaphone CELL682. The antenna allows you to place your CELL682 in a location that would normally have reduced signal contact (such as in a metal cabinet).

One Year Comunication Service

Product # FGD-CELL1Y

One Year Communication Service

Sensaphone SAT4D One Year Communications Service

Product # FGD-SAT1Y

Sensaphone SAT4D One Year Communications Service

Pole Mount Kit for SAT4D

Product # FGD-SAT4D-PKIT

This kit provides all of the necessary parts to mount the SAT4D product onto a pole that is installed directly into the ground.

Sensaphone Web600 Battery Backup

Product # FGD-W610-B

WSG Wireless Spot Water Sensor

Product # FGD-WSG30-SPOT

The WSG30 Wireless Spot Water Detection Sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and water sensing probes for monitoring for the presence of water at a particular location. The sensor comes with three AA alkaline batteries which will power the sensor for up to two years.

WSG Wireless 4-20mA Sensor

Product # FGD-WSG30-4-20

The WSG30 Wireless 4-20mA sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter, 4-20mA input and a 24V loop power supply. The sensor can be used to monitor the output of any 4-20mA transducer. The sensor comes with a plug-in power supply and three AA alkaline batteries which will power the sensor for several hours if main AC power fails.

WSG Wireless Dry Contact Sensor

Product # FGD-WSG30-DRY

The WSG Wireless Dry Contact sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and input terminals for connecting to any normally-open or normally closed output. (Use of this device with solid-state outputs is not recommended.) The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails.

WSG Wireless Humidity Sensor

Product # FGD-WSG30-HUM

The WSG Wireless Humidity Sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and humidity sensor element for monitoring humidity wherever the device is installed. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails.

WSG Wireless Power Failure Sensor

Product # FGD-WSG30-PWR

The WSG Wireless Power Failure sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter, two AA alkaline batteries and a wall plug in power supply. The sensor will detect a loss of power at the outlet where the power supply is attached. The two AA alkaline batteries will power the sensor and allow it to transmit alarm information in the event that 120VAC power fails.

WSG Wireless Temperature Sensor

Product # FGD-WSG30-TMP

The WSG Wireless Temperature sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and temperature element for monitoring temperature wherever the device is installed. You can remove the internal temperature element and attach a remote temperature probe so that measurements can be made in a refrigerator, freezer or other harsh environment. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails.

WSG Wireless Temperature Sensor with External Probe

Product # FGD-WSG30-TEX

The WSG Wireless Temperature sensor with External Probe is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and a remote temperature probe so that temperature measurements can be made in a refrigerator, freezer or other harsh environments. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails.

WSG Wireless Zone Water Detection Sensor

Product # FGD-WSG30-ZONE

The WSG30 Wireless Zone Water Detection Sensor is designed to work with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and ten feet of water sensing cable for monitoring for the presence of water in a particular area. The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope. You can connect up to ten lengths of WaterRope (100′) to one Zone Water Detector. The sensor comes with three AA alkaline batteries which will power the sensor for up to two years.

IMS-4000 Enterprise Monitoring Node Expansion Unit

Product # IMS-4002

The IMS-4000 Node allows IMS-4000 users to expand their infrastructure and monitor additional inputs in locations away from the IMS-4000 Host. Up to thirty-one Nodes can be used with each IMS-4000 Host. Much like the Host, the Node can monitor eight inputs for environmental conditions and or alarm contacts from other computer equipment such as UPS systems. The Node connects to the Host via a RJ-45 10/100BASE-T Ethernet and is monitored via the ConsoleView software included with the Host.

IMS-4000 Enterprise Monitoring International Node Expansion Unit

Product # IMS-4003

The IMS-4000 Node allows IMS-4000 users to expand their infrastructure and monitor additional inputs in locations away from the IMS-4000 Host. Up to thirty-one Nodes can be used with each IMS-4000 Host. Much like the Host, the Node can monitor eight inputs for environmental conditions and or alarm contacts from other computer equipment such as UPS systems. The Node connects to the Host via a RJ-45 10/100BASE-T Ethernet and is monitored via the ConsoleView software included with the Host.

IMS-4000 Dry Contact Node

Product # IMS-4010

The IMS-4000 Dry Contact Node provides eight dry contact inputs (normally open/normally closed) and works in conjunction with the IMS Host. The device communicates with the IMS-4000 Host via its Ethernet connection. The Dry Contact Node is a cost-effective solution when your application only requires monitoring of dry contacts. With this device you do not need to use Dry Contact Bridges, thus reducing cost, installation time, and space. This device includes four AA rechargeable NiMH batteries for power backup in the event of a power failure. Both main power and battery charge are monitored and can be programmed to trip alarms as well. The unit comes in a black plastic enclosure with tabs for wall mounting. Rubber feet are also included for placement on a shelf/desktop.

IMS-4000 Receiver Node for Wireless Sensors

Product # IMS-4200

The IMS-4000 Receiver Node for Wireless Sensors extends the environmental monitoring capability of your IMS-4000 system by implementing Wireless Sensor technology. The Receiver Node can work with up to 8 wireless sensors. The unit will wirelessly communicate with the sensors, then transmit their status back to your IMS-4000 host via its Ethernet connection. Wireless sensors are available to monitor Temperature, Humidity, Water on the Floor, Power, Dry Contacts, and 4-20mA signals. The sensors use mesh networking technology to create multiple communication paths between the sensors and the Receiver Node to ensure reliable communications. Sensors can also be battery powered for those installations where an outlet may not be available. A LCD is provided to show the status of all wireless sensors. The unit is powered by a plug-in adapter and has a 6V 1.3 AH rechargeable backup battery located inside the enclosure. Circuitry in the unit will maintain precise charging of the battery system. The unit comes in a rugged plastic enclosure with tabs for wall mounting. Connections for an antenna, power supply, and Ethernet are easily accessible from the top and bottom of the unit.

IMS-4000 Receiver International Node for Wireless Sensors

Product # IMS-4200-INT

The IMS-4000 Receiver Node for Wireless Sensors extends the environmental monitoring capability of your IMS-4000 system by implementing Wireless Sensor technology. The Receiver Node can work with up to 8 wireless sensors. The unit will wirelessly communicate with the sensors, then transmit their status back to your IMS-4000 host via its Ethernet connection. Wireless sensors are available to monitor Temperature, Humidity, Water on the Floor, Power, Dry Contacts, and 4-20mA signals. The sensors use mesh networking technology to create multiple communication paths between the sensors and the Receiver Node to ensure reliable communications. Sensors can also be battery powered for those installations where an outlet may not be available. A LCD is provided to show the status of all wireless sensors. The unit is powered by a plug-in adapter and has a 6V 1.3 AH rechargeable backup battery located inside the enclosure. Circuitry in the unit will maintain precise charging of the battery system. The unit comes in a rugged plastic enclosure with tabs for wall mounting. Connections for an antenna, power supply, and Ethernet are easily accessible from the top and bottom of the unit.

IMS-4000 Wireless Temperature Sensor

Product # IMS-4210

The IMS-4210 Wireless Temperature sensor provides remote temperature monitoring without running wires. Temperature data is sent from the sensor to the IMS-4200 wireless node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available, in which case the batteries function as backup power if main AC power fails (power supply required for router mode).

IMS-4000 Wireless External Temperature Sensor

Product # IMS-4210-E

The IMS-4210-E Wireless External Temperature sensor provides remote temperature monitoring without running wires. The sensor includes an external probe with 12′ of wire and is intended for monitoring temperatures in refrigerator/freezers or other harsh environments. Temperature data is sent from the sensor to the IMS-4200 wireless node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-ofsite. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available, in which case the batteries function as backup power if main AC power fails (power supply required for router mode).

IMS-4000 Wireless Humidity Sensor

Product # IMS-4211

The IMS-4211 Wireless Humidity sensor provides remote humidity monitoring without running wires. Data is sent from the sensor to the IMS-4200 Wireless Node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available, in which case the batteries function as backup power if main AC power fails (power supply required for router mode).

IMS-4000 Wireless Dry Contact Sensor

Product # IMS-4212

The IMS-4212 Wireless Dry Contact sensor provides remote contact monitoring without running wires. Contact data is sent from the sensor to the IMS-4200 Wireless Node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available, in which case the batteries function as backup power if main AC power fails (power supply required for router mode).

IMS-4000 Wireless Power Sensor

Product # IMS-4213

The IMS-4213 Wireless Power sensor provides remote power monitoring without running wires. The power status is monitored by the wall plug in adapter and sent from the sensor to the IMS-4200 Wireless Node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). A plug-in power supply is included. The batteries function as backup power when main AC power fail.

IMS-4000 Wireless 4-20mA Sensor

Product # IMS-4214

The IMS-4214 Wireless 4-20mA sensor provides remote monitoring of 4-20mA transducers without running wires. The 4-20mA signal is sent from the sensor to the IMS-4200 Wireless Node via an integrated 2.4GHz wireless radio. An internal 24V DC supply is built-in to power the current loop. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a lowpower battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/ router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor when main power fails. A plug-in power supply is included.

IMS-4000 Wireless Spot Water Detection Sensor

Product # IMS-4215

The IMS-4215 Wireless Spot Water Detection Sensor provides remote leak detection monitoring without running wires. The sensor has four probes on the bottom of the enclosure which will trigger an alarm when any adjacent pair get wet. Alarm information is sent from the sensor to the IMS-4200 Wireless node via an integrated 2.4GHz Wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. This sensor is battery operated only, and cannot be used as a router. Simply place the sensor on the floor in the area to be monitored. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years.

IMS-4000 Wireless Zone Water Detection Sensor

Product # IMS-4216

The IMS-4215 Wireless Zone Water Detection Sensor provides remote leak detection monitoring without running wires. The sensor comes with 10′ of leak detection cable which can be installed around equipment or under a raised flooring system. The detection cable can be extended to cover larger areas by connecting additional 10′ lengths. Alarm information is sent from the sensor to the wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available, in which case the batteries function as backup power if main AC power fails (power supply required for router mode). IMS-4200 Wireless node via an integrated 2.4GHz

IMS-4000 Wireless Sensor A/C Power Supply

Product # IMS-4250

IMS-4000 Wireless Sensor A/C Power Supply- International Plug

Product # IMS-4251

IMS-4000 PowerGate

Product # IMS-4301

The IMS-4000 PowerGate allows you to manually or automatically switch up to 8 electrical outlets from the IMS-4000 ConsoleView Software or the IMS-4000 web page. This gives you the ability to remotely turn-on, turn-off, or cycle power (reboot) remote equipment. You can also program the system to automatically control the power to a device based on an alarm condition. The PowerGate has eight LEDs on the front panel to indicate outlet status and a 15 Amp circuit breaker for safety. It can switch a total of up to 12 amps of current at 120VAC 60Hz (all outlets combined). The unit is made for rack mounting and fits in a 1 EIA rack space (17″w x 10″d x 1.75″h).

IMS-4000 PowerGate 2

Product # IMS-4302

The IMS-4000 PowerGate2 allows you to manually or automatically switch up to 8 electrical outlets from the IMS-4000 ConsoleView Software or the IMS-4000 web page. This gives you the ability to remotely turn-on, turn-off, or cycle power (reboot) remote equipment. You can also program the system to automatically control the power to a device based on an alarm condition. The PowerGate2 features individual power input circuits for each outlet thus giving you the ability to distribute the power load across multiple circuits. Two of the outlets can switch up to 10 amps (120VAC 60Hz) and the other six can switch up to 4 Amps (120VAC 60Hz). The unit is made for rack mounting with steel brackets and fits in a 1 EIA rack space (17″w x 12″d x 1.75″h).

IMS-4000 Dual Relay Output Module

Product # IMS-4310

The IMS-4310 Dual Relay Output Module allows you to control two devices from any IMS-4000 Host or Node. Each output may be controlled either manually or automatically. Each output has the option of providing either a dry relay contact or 12VDC power. Two switches located inside the device select the output type.

IMS 7' CAT5 Patch Cable Green

Product # IMS-4402

Standard Cat5 Ethernet cable to used for connecting IMS sensors to an IMS-4000 Host, IMS-4000 Node, or IMS-1000.

IMS 14' CAT5 Patch Cable Black

Product # IMS-4403

Standard Cat5 Ethernet cable to used for connecting IMS sensors to an IMS-4000 Host, IMS-4000 Node, or IMS-1000.

IMS 25' CAT5 Patch Cable Black

Product # IMS-4404

Standard Cat5 Ethernet cable to used for connecting IMS sensors to an IMS-4000 Host, IMS-4000 Node, or IMS-1000.

IMS RJ45 Cable Couplers (F/F)

Product # IMS-4405

Connects two Cat5 cables to extend the distance to the IMS sensor. This kit comes with a set of four connectors.

IMS-4000 Wall Mount Bracket

Product # IMS-4406

Allows the IMS-4000 Host to be mounted flat to a wall instead of being mounted in a 19″ rack.

IMS-4000 DB9 Null Modem Cable

Product # IMS-4407

Replacement cable used to connect a computer to an IMS-4000 Host for initial network configuration.

Extra IMS-4000 Solution Manual

Product # IMS-4408

Additional copy of the IMS-4000 Owner's Manual.

Extra ConsoleView Software CD

Product # IMS-4409

Additional copy of the IMS-4000 Console View PC software.

Extra IMS-1000 Solution Manual

Product # IMS-4410

Additional copy of the IMS-1000 Owner's Manual.

IMS-4000 Right Angel Power Cord for PG2

Product # IMS-4413

Optional power cords for the IMS-4000 PowerGate2 outlet switching device.

IMS Network Camera, Panasonic Pan Tilt

Product # IMS-4421

The Panasonic BLC111A network camera is ideal for monitoring your small business property, data center, or residence. The camera can be used in combination with the IMS-1000 or IMS-4000 systems to send camera snapshots via e-mail when alarms are detected.
The camera features a 10x digital zoom function in addition to remote pan and tilt controls. This allows you to control the direction of the camera right from your web browser. The camera also has a built-in microphone so that you can hear sounds from the remote site as well. A privacy mode can be activated either at the camera, or remotely in administrator mode, which will cover the lens.

IMS Network Camera, Axis

Product # IMS-4423

The Axis M1011 is a small network camera ideal for monitoring your small business property, data center, or residence. The camera can be used in combination with the IMS-1000 or IMS-4000 systems to send camera snapshots via e-mail when alarms are detected.
The camera offers a high quality yet affordable video surveillance solution. Using progressive scan technology, the camera provides VGA images of moving objects without motion blur.
Designed to compliment modern interiors and easy to install and use, the M1011 will not look out of place in the home or office and is ideal for IP camera novices. The Axis M1011 IP security camera has a built-in web server and can be viewed over a Local Area Network (LAN), Wide Area Network (WAN) or via the Internet as a streaming IP webcam.

IMS Room Temperature Sensor

Product # IMS-4810

The IMS-4810 temperature sensor is designed to connect to the Sensaphone IMS series product line and monitor indoor temperatures. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or to a single-gang electrical box.
The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS Room Temperature Sensor (°F) w/LCD Readout

Product # IMS-4811

The IMS-4811 temperature sensor is designed to connect to the Sensaphone IMS series product line and monitor indoor temperatures. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or to a single-gang electrical box.
The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS Mini Temperature Sensor

Product # IMS-4812

The IMS-4812 Mini Temperature Sensor is designed to connect to the Sensaphone IMS series product line and monitor temperatures in tight locations (for example, inside equipment racks). The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor may be secured inside equipment using double-sided tape (included) or with tie-wraps.
The Mini-Temperature Sensor comes with an attached 7′ cable with a RJ-45 plug on the end. If the sensor is close to the IMS unit, you can plug the sensor directly to an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS Room Temperature Sensor (°C) w/LCD Readoutt

Product # IMS-4813

The IMS-4813 temperature sensor is designed to connect to the Sensaphone IMS series product line and monitor indoor temperatures. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or to a single-gang electrical box.
The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS Ultra Low Temperature Sensor

Product # IMS-4814

The IMS-4814 Ultra Low Temperature Sensor is designed to connect to the Sensaphone IMS product line and monitor temperatures in refrigerators or freezers. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor probe may be secured inside equipment using the included clamp or it may be hung using tie wraps. Do not install the black plastic enclosure inside of a refrigerator or freezer. It is available with an optional NIST temperature certification.
The Ultra Low Temperature Sensor comes with an attached 7′ cable with an RJ-45 plug on the end and a weatherproof probe with 12′ of cable. If the sensor installation is close to the IMS unit, you can plug it directly into an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input.

IMS Ultra Low Temperature Sensor w/Calibration Certification

Product # IMS-4814-NIST

The IMS-4814 Ultra Low Temperature Sensor is designed to connect to the Sensaphone IMS product line and monitor temperatures in refrigerators or freezers. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor probe may be secured inside equipment using the included clamp or it may be hung using tie wraps. Do not install the black plastic enclosure inside of a refrigerator or freezer. It is available with an optional NIST temperature certification.
The Ultra Low Temperature Sensor comes with an attached 7′ cable with an RJ-45 plug on the end and a weatherproof probe with 12′ of cable. If the sensor installation is close to the IMS unit, you can plug it directly into an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input.

IMS Temperature w/Glass Bead Vial

Product # IMS-4815

The IMS-4815 Temperature Sensor is designed to connect to the Sensaphone IMS series product line. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm such as defrost cycles, opening of doors and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. This is a highly recommended sensor for every cold storage application.
The Temperature Sensor comes with an attached 7′ cable with an RJ-45 plug on the end and a weatherproof probe with 12′ of cable. If the sensor is close to the IMS unit, you can plug the sensor directly to an IMS environmental input. If the cable is too short you can use a RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via a RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the IMS unit environment input.

IMS External Probe Temperature Sensor

Product # IMS-4816

The IMS-4816 Temperature Sensor with External Probe is designed to connect to the Sensaphone IMS product line and monitor temperatures in areas where a traditional sensor won't fit. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor probe may be secured inside equipment using the included clamp or it may be hung using tie wraps. Do not install the black plastic enclosure inside of a refrigerator or freezer.
The Temperature Sensor with External Probe comes with an attached 7′ cable with an RJ-45 plug on the end and a weatherproof probe with 12′ of cable. If the sensor installation is close to the IMS unit, you can plug it directly into an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input.

IMS Room Humidity Sensor

Product # IMS-4820

The IMS-4820 humidity sensor is designed to connect to the Sensaphone IMS series product line and monitor indoor humidity levels. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or to a single-gang electrical box. The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS Humidity Sensor w/LCD Readout

Product # IMS-4821

The IMS-4821 humidity sensor is designed to connect to the Sensaphone IMS series product line and monitor indoor humidity. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or to a single-gang electrical box. The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input.

IMS Water Sensor w/10' Water

Product # IMS-4830

The IMS-4830 Water Detection Sensor protects your server and equipment from damaging water leaks from malfunctioning HVAC systems, cafeteria accidents, or any general plumbing failures in your facilities. The IMS-4830 is powered directly by the IMS unit.
After mounting the sensor, attach the included 10′ of WaterRope, and simply lay its orange cable around your equipment: place it on the floor or beneath a raised floor; inside a dropceiling or in the rafters between floors; or anywhere you must know about water near your equipment.
You can attach additional Water Detection sensors to each other to expand your water leak detection capabilities throughout your facility; alternatively, IMS WaterRopes are designed to plug into each other to widen your perimeter for any individual sensor.

Extra 10' Water Detection Rope

Product # IMS-4831

Extends the water detection rope on the IMS-4830 sensor by an additional 10 feet.

IMS External Power Sensor (110/220VAC)

Product # IMS-4840

The IMS-4840 External Power Sensor lets you monitor power anywhere within your infrastructure. It reports any loss of power and measures the current voltage in the circuit, allowing you to know the status of each server rack and even of your remote UPS. Any failed generator starts are reported to you immediately. The IMS-4840 can monitor voltage from 0-250VAC 50/60Hz. The Power Sensor connects to the IMS Host or Node via an RJ-45 cable (e.g. CAT5 cable). The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS AC Current Sensor, up to 15 Amps, C13/C14

Product # IMS-4841

The IMS-4841 15A Current Sensor lets you monitor current consumption of a particular device or circuit anywhere within your infrastructure. It reports the actual current flow in the circuit, allowing you to know the current draw from devices such as server racks, UPS and generators. Any failed generator starts are reported to you immediately. The IMS-4841 can monitor current from 0-15 amps over a voltage range from 0-250VAC 50/60Hz. The sensor comes with IEC320 C14 inlet and C13 outlet connectors.

IMS AC Current Sensor, up to 20 Amps, C19/C20

Product # IMS-4842

The IMS-4842 20A Current Sensor lets you monitor current consumption of a particular device or circuit anywhere within your infrastructure. It reports the actual current flow in the circuit, allowing you to know the current draw from devices such as server racks, UPS and generators. Any failed generator starts are reported to you immediately. The IMS-4842 can monitor current from 0-20 Amps over a voltage range from 0-250VAC 50/60Hz. The sensor comes with IEC320 C20 inlet and C19 outlet connectors.

IMS Dry Contact Bridge

Product # IMS-4850

The IMS-4850 Dry Contact Bridge allows you to connect a dry contact alarm from any device to your IMS. The Dry Contact Bridge is compatible with Normally Open and Normally Closed contacts. The electrical connection between the sensor and IMS is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or rest on the floor.
The Dry Contact Bridge connects to the IMS via a RJ-45 cable (e.g. CAT5 cable). The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the bridge to your structured wiring network via a RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS 4-20mA Bridge

Product # IMS-4851

The 4-20mA Bridge allows you to connect a 4-20mA transducer to your Sensaphone IMS unit. The 4-20mA Bridge features optical isolation between the input and the IMS unit, which ensures troublefree operation and safety. The electrical connection between the bridge and IMS is made via RJ-45 patch cable (not included). The bridge may be mounted either on a wall or rest on the floor. The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the bridge may be installed in another room or another floor. Connect the bridge to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS Door Switch

Product # IMS-4860

The IMS-4860 Door Switch with bridge enables your IMS unit to detect if any unauthorized entry or intrusion has occurred. The bridge may be mounted either on a wall or rest on the floor. The switch is mounted to doors or windows you wish to monitor. The electrical connection between the bridge and IMS unit is made via RJ-45 patch cable.
The connection from the bridge to Host or Node can utilize your existing network wiring infrastructure. For example, the switch may be installed in another room or another floor. Connect the bridge to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

IMS Passive Infrared Motion Sensor

Product # IMS-4861

The IMS-4861 Passive Infrared Detection Sensor is a dual-element passive infrared intrusion detector for use in electronic security systems. It reduces FALSE alarms by eliminating background noises and nuisance stimuli. The IMS-4861 employs variable pulse-count adjustment, thus making it adaptable for use both inside and outside of server/equipment rooms. It is designed to connect to the IMS Host or Node.
The Passive Infrared Detection Sensor comes with an attached 7′ cable with an RJ-45 plug on the end. If the sensor is close to the IMS Host or Node, you can plug the sensor directly to an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length.

IMS Smoke Detector Sensor

Product # IMS-4862

The IMS-4862 Smoke Detector Sensor is designed to connect to the IMS Host or Node and monitor for smoke in indoor environments. The electrical connection between the sensor and IMS is made via the attached RJ-45 patch cable. The sensor may be secured to a wall or ceiling (hardware not included).
If the sensor is close to the IMS Host or Node, you can plug the sensor directly to an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input.

IMS Airflow Sensor

Product # IMS-4863

The Airflow sensor is designed to monitor for the presence or absence of cool moving air. This is especially useful for monitoring air conditioning systems. The sensor can provide relative air flow as a percentage from 0 to 100. The sensor is compatible with both the IMS-1000 and IMS-4000 devices. The Airflow Sensor connects to the IMS via a RJ-45 cable (e.g. CAT5 cable). The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the bridge to your structured wiring network via a RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.

Wireless Dry Contact Sensor

Product # WSR-0101

The WSR-0101 Wireless Indoor Dry Contact sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and input terminals for connecting to any normally-open or normally closed output. (Use of this device with solid-state outputs is not recommended.) The sensor comes with 3 AAA alkaline batteries which will power the sensor for up to 3 years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails.

Wireless Temperature Sensor

Product # WSR-0100

The WSR-0100 Wireless Indoor Temperature sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and temperature element for monitoring temperature wherever the device is installed. You can also remove the internal temperature element and connect a remote temperature probe so that measurements can be made in a refrigerator, freezer or other harsh environment. The sensor comes with 3 AAA alkaline batteries which will power the sensor for up to 3 years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails.

Wireless Power Failure Sensor

Product # WSR-0102

The WSR-0102 Wireless Indoor Power Failure sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter, AAA alkaline batteries and a wall plug in power supply. The sensor will detect a loss of power at the outlet where the power supply is attached. The 3 AAA alkaline batteries will power the sensor and allow it to transmit alarm information in the event that AC power fails.

Wireless Humidity Sensor

Product # WSR-0103

The WSR-0103 Wireless Indoor Humidity sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and humidity sensor element for monitoring humidity wherever the device is installed. The sensor comes with 3 AAA alkaline batteries which will power the sensor for up to 3 years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails.

Wireless 4-20mA Sensor

Product # WSR-0104

The WSR-0104 Wireless Indoor 4-20mA sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter, 4-20mA input and a 24V loop power supply. The sensor can be used to monitor the output of any 4-20mA transducer. The sensor comes with a plug-in power supply and 3 AAA alkaline batteries which will power the sensor for several hours if main AC power fails.

Wireless Motion Detector

Product # WSR-0105

A waterproof device for measuring the temperature of fluids in a pipe. It features a 304 stainless steel probe and a brass WEL-B thermowell. Comes with 8 feet of wire.

Wireless Spot Water Detection Sensor

Product # WSR-0106

The WSR-0106 Wireless Spot Water Detection Sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and water sensing probes for monitoring for the presence of water at a particular location. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 3 years.

Wireless Zone Water Detection Sensor

Product # WSR-0107

The WSR-0107 Wireless Zone Water Detection Sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and ten feet of water sensing cable for monitoring for the presence of water in a particular area. The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope. You can connect up to ten lengths of WaterRope (100′) to one Zone Water Detector. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 3 years.

AC Power Adaptor for 2800 Wireless Sensors

Product # WSR-0190

Provides AC power for a Model 2800 wireless sensor so batteries are only used during a power failure.

Wireless Repeater

Product # WSR-0199

The WSR-0199 Wireless Repeater is designed to work with the Sensaphone 2800 Environmental Monitoring System. The wireless repeater allows you to have a greater distance between your wireless sensors and the Sensaphone 2800. It contains a more powerful radio transceiver which can transmit up to 300′ indoors and up to 4,000′ (line-of-sight). Only one repeater can be used per Sensaphone 2800. The sensor comes with a plug-in power supply and 3 AAA alkaline batteries for back-up in the event of an AC power failure.

12V Power Supply for Thermostat

Product # XFR-0024

Required to supply power to the FGD-0064 Remote setback thermostat.